+34 934 616 742 Barcelona, Spain Seixal, Portugal

Application Conformal Coating

The Board inverter turns a board upside down to make processing possible on both sides without manual intervention. A board transfer cycle consists of infeed, flip or no-flip, and outfeed. Up to 10 different board transfer cycles can be stored. The machine is bi-directional and can receive and send boards both up- and downstreams.

The Dual lane conveyor is the first product in a continuing series of Dual lane equipment. Each lane has its own standard SMEMA interface, which makes the conveyor easy to install in a dual lane electronics assembly line. Conveyor width adjustment is motorized.

The Dual lane conveyor is the first product in a continuing series of Dual lane equipment. Each lane has its own standard SMEMA interface, which makes the conveyor easy to install in a dual lane electronics assembly line. Conveyor width adjustment is motorized.

The FIFO Buffer 10 has an advanced optional cooling function and is designed to balance station-capacity differences by offering board escape possibilities in case of failures or slow board flow in the connected systems. Buffer full warning level, start slot, stepping (pitch), pass through slot and cooling time are adjustable from the operators panel.

Up and Down Lift for pallets and solder frames, to be placed in the beginning or end of a production line. Standard or special infeed and outfeed heights.

Application SMT Line

The Loader separates and loads bare or pre-mounted PC-Boards from rasterized magazines, onto a subsequent production line.

The Reloader separates and loads bare or pre-mounted PC-Boards from rasterized magazines, onto a subsequent production line, waits for the board to return, and receives the processed board into its original magazine slot.

The Unloader unloads the production line and loads bare or pre-mounted PCBoards into rasterized magazines.

The Board inverter turns a board upside down to make processing possible on both sides without manual intervention. A board transfer cycle consists of infeed, flip or no-flip, and outfeed. Up to 10 different board transfer cycles can be stored. The machine is bi-directional and can receive and send boards both up- and downstreams.

The board transfer system is a sophisticated solution for dividing, merging, or rerouting production lines by transferring boards between them. The machine consists of a traverse unit and a board carrying shuttle conveyor.

The Buffer unit is designed to balance station-capacity differences by offering board escape possibilities in case of failures or slow board flow in the connected systems.

The Destacker separates a batch of PCBs and transports them one by one to the following machine.

The Dual lane conveyor is the first product in a continuing series of Dual lane equipment. Each lane has its own standard SMEMA interface, which makes the conveyor easy to install in a dual lane electronics assembly line. Conveyor width adjustment is motorized.

The Turn unit routes boards from 1, 2 or 3 infeed sides, to 1, 2 or 3 outfeed sides. Board infeed/outfeed routing can be fixed, based on board flow, and/or based on priority values set via the control panel. Outfeed routing can also be controlled by external signals such as Good/No Good board or by a barcode reader.

The Dual Unloader consists of a conveyor mounted on an Y/Z table that receives and distributes PCBs from an upstream machine into one or two magazines, depending on selected work mode. If the pass/fail function is activated, good and bad PCBs will be separated and stored in different magazines.

The FIFO Buffer 10 has an advanced optional cooling function and is designed to balance station-capacity differences by offering board escape possibilities in case of failures or slow board flow in the connected systems. Buffer full warning level, start slot, stepping (pitch), pass through slot and cooling time are adjustable from the operators panel.

The Magazine buffer is placed in the line to balance board flow in FIFO or LIFO buffer mode, act as a line splitter in Loader or Unloader mode, or line merger in Pass through mode. The magazine can be removed/exchanged at any time in all work modes.

The large board conveyor is based on the standard transport/buffer conveyor with the following main differences: reinforced rail structure, rail suspension, and belt driving mechanism. Each section of the conveyor has its own powerful DC motor that drives the belt on both sides, and provides smooth, reliable transportation of PCBs through an electronics assembly line.

The Light Conveyor is a cost effective product, aimed at customers that are interested in endless reliability, very low maintenance and safe transportation of PCBs through an electronics assembly line, without the advanced functions and optional accessories offered by our high-end conveyors.

The Loader separates and loads bare or pre-mounted PC-Boards from rasterized magazines, onto a subsequent production line.

The Unloader unloads the production line and loads bare or pre-mounted PCBoards into rasterized magazines.

The manual gate conveyor allows people and vehicles to go through, rather than round a complete line. It consists of two conveyor sections, one fixed and one jointed.

The Mini buffer consists of a vertical buffer and a 500mm conveyor, and is placed in the line to balance board flow in LIFO buffer mode, act as a line splitter in Loader or Unloader mode, or good/bad board separator in Triggered mode. Width adjustment, work mode, and other functions, are all accessed from the hand control unit, which makes the unit easily managed.

The PCB reject & inspection lift is an option for 1000mm and 1500mm conveyors, and enables Good or No Good PCB separation and inspection. The lift has three different work modes. Reject mode, inspection mode, and pass through.

The Loader separates and loads bare or pre-mounted PC-Boards from rasterized magazines, onto a subsequent production line.

The Unloader unloads the production line and loads bare or pre-mounted PCBoards into rasterized magazines.

The Single reloader separates and loads bare or pre-mounted PC-Boards from rasterized magazines, onto a subsequent production line, waits for the board to return, and receives the processed board into its original magazine slot.

The T3 conveyor is a sectioned conveyor with a rigid framework. Each side and section of the conveyor has its own motor, belt and board-present sensor, enabling a board to be buffered on each section and provide smooth, reliable transportation of PCBs.Length from 500 mm to 2500 mm.

The T3 workstation is built around the standard T3 conveyor and enables manual assembly work and inspections to be carried out on PCBs in-line. Each side and section of the conveyor has its own motor and belt, providing smooth and reliable transportation of PCBs.

The T4 conveyor is a sectioned conveyor with a rigid framework. Each side and section of the conveyor has its own motor, belt and board-present sensor, enabling a board to be buffered on each section and provide smooth, reliable transportation of PCBs.

The T4 workstation is built around the standard T4 conveyor and enables manual assembly work and inspections to be carried out on PCBs in-line. Each side and section of the conveyor has its own motor and belt, providing smooth and reliable transportation of PCBs.

The Telescopic gate conveyor is a fully automated pass through conveyor that allows people and vehicles to go through, rather than round a complete line. Since the retracted position of the telescopic conveyor is its idle position there is no need to press any buttons to pass through the line.

The Turn unit routes boards from 1, 2 or 3 infeed sides, to 1, 2 or 3 outfeed sides. Board infeed/outfeed routing can be fixed, based on board flow, and/or based on priority values set via the control panel. Outfeed routing can also be controlled by external signals such as Good/No Good board or by a barcode reader.

Buffer

The Buffer unit is designed to balance station-capacity differences by offering board escape possibilities in case of failures or slow board flow in the connected systems.

The Dual lane conveyor is the first product in a continuing series of Dual lane equipment. Each lane has its own standard SMEMA interface, which makes the conveyor easy to install in a dual lane electronics assembly line. Conveyor width adjustment is motorized.

The Magazine buffer is placed in the line to balance board flow in FIFO or LIFO buffer mode, act as a line splitter in Loader or Unloader mode, or line merger in Pass through mode. The magazine can be removed/exchanged at any time in all work modes.

The Mini buffer consists of a vertical buffer and a 500mm conveyor, and is placed in the line to balance board flow in LIFO buffer mode, act as a line splitter in Loader or Unloader mode, or good/bad board separator in Triggered mode. Width adjustment, work mode, and other functions, are all accessed from the hand control unit, which makes the unit easily managed.

Conveyors

The large board conveyor is based on the standard transport/buffer conveyor with the following main differences: reinforced rail structure, rail suspension, and belt driving mechanism. Each section of the conveyor has its own powerful DC motor that drives the belt on both sides, and provides smooth, reliable transportation of PCBs through an electronics assembly line.

The Light Conveyor is a cost effective product, aimed at customers that are interested in endless reliability, very low maintenance and safe transportation of PCBs through an electronics assembly line, without the advanced functions and optional accessories offered by our high-end conveyors.

The T3 conveyor is a sectioned conveyor with a rigid framework. Each side and section of the conveyor has its own motor, belt and board-present sensor, enabling a board to be buffered on each section and provide smooth, reliable transportation of PCBs.Length from 500 mm to 2500 mm.

The T3 workstation is built around the standard T3 conveyor and enables manual assembly work and inspections to be carried out on PCBs in-line. Each side and section of the conveyor has its own motor and belt, providing smooth and reliable transportation of PCBs.

The T4 conveyor is a sectioned conveyor with a rigid framework. Each side and section of the conveyor has its own motor, belt and board-present sensor, enabling a board to be buffered on each section and provide smooth, reliable transportation of PCBs.

The T4 workstation is built around the standard T4 conveyor and enables manual assembly work and inspections to be carried out on PCBs in-line. Each side and section of the conveyor has its own motor and belt, providing smooth and reliable transportation of PCBs.

Dual Lane

The Dual lane conveyor is the first product in a continuing series of Dual lane equipment. Each lane has its own standard SMEMA interface, which makes the conveyor easy to install in a dual lane electronics assembly line. Conveyor width adjustment is motorized.

The Turn unit routes boards from 1, 2 or 3 infeed sides, to 1, 2 or 3 outfeed sides. Board infeed/outfeed routing can be fixed, based on board flow, and/or based on priority values set via the control panel. Outfeed routing can also be controlled by external signals such as Good/No Good board or by a barcode reader.

Gates

The manual gate conveyor allows people and vehicles to go through, rather than round a complete line. It consists of two conveyor sections, one fixed and one jointed.

The Telescopic gate conveyor is a fully automated pass through conveyor that allows people and vehicles to go through, rather than round a complete line. Since the retracted position of the telescopic conveyor is its idle position there is no need to press any buttons to pass through the line.

Loaders/Unloaders

The Loader separates and loads bare or pre-mounted PC-Boards from rasterized magazines, onto a subsequent production line.

The Reloader separates and loads bare or pre-mounted PC-Boards from rasterized magazines, onto a subsequent production line, waits for the board to return, and receives the processed board into its original magazine slot.

The Unloader unloads the production line and loads bare or pre-mounted PCBoards into rasterized magazines.

The Dual Unloader consists of a conveyor mounted on an Y/Z table that receives and distributes PCBs from an upstream machine into one or two magazines, depending on selected work mode. If the pass/fail function is activated, good and bad PCBs will be separated and stored in different magazines.

The Loader separates and loads bare or pre-mounted PC-Boards from rasterized magazines, onto a subsequent production line.

The Unloader unloads the production line and loads bare or pre-mounted PCBoards into rasterized magazines.

The Loader separates and loads bare or pre-mounted PC-Boards from rasterized magazines, onto a subsequent production line.

The Single reloader separates and loads bare or pre-mounted PC-Boards from rasterized magazines, onto a subsequent production line, waits for the board to return, and receives the processed board into its original magazine slot.

The Unloader unloads the production line and loads bare or pre-mounted PCBoards into rasterized magazines.

Other

The Board inverter turns a board upside down to make processing possible on both sides without manual intervention. A board transfer cycle consists of infeed, flip or no-flip, and outfeed. Up to 10 different board transfer cycles can be stored. The machine is bi-directional and can receive and send boards both up- and downstreams.

The board transfer system is a sophisticated solution for dividing, merging, or rerouting production lines by transferring boards between them. The machine consists of a traverse unit and a board carrying shuttle conveyor.

The Destacker separates a batch of PCBs and transports them one by one to the following machine.

The PCB reject & inspection lift is an option for 1000mm and 1500mm conveyors, and enables Good or No Good PCB separation and inspection. The lift has three different work modes. Reject mode, inspection mode, and pass through.

The Turn unit routes boards from 1, 2 or 3 infeed sides, to 1, 2 or 3 outfeed sides. Board infeed/outfeed routing can be fixed, based on board flow, and/or based on priority values set via the control panel. Outfeed routing can also be controlled by external signals such as Good/No Good board or by a barcode reader.

Up and Down Lift for pallets and solder frames, to be placed in the beginning or end of a production line. Standard or special infeed and outfeed heights.