+34 934 616 742 Barcelona, Spain Seixal, Portugal

Pre-Heaters

Forget about thermal stress

The application of JBC preheaters is indispensable for rework on multi-layered PCBAs and/or large ground planes in order to avoid thermal stress and facilitate soldering as well as desoldering processes.

For an optimal result it is necessary to preheat the PCB and its components with controlled temperature profiles within the recommended limit values for each application. JBC preheaters feature temperature profiles specially designed for this purpose and customizable according to need.

With the software JBCSuite the preheater can be synchronized with other JBC hot-air, soldering as well as fume extractor equipment in order for them to work jointly and to perform your rework process optimally.

PHNK Nano Preheater Set

It features three work modes:

Power Mode allows working at a fixed power level with the option of using protection thermocouple.

Temperature Mode keeps the PCBA at a selected temperature, using the regulation thermocouple and, optionally, protection thermocouples.

Profile Mode allows control of the heating rate of the PCBA by the use of a control and protection thermocouple, without exceeding the recommended limit levels in each application. It features 22 customizable profiles.

Two thermocouple can be connected in any of the three work modes.

PSN Nano PBC Support is perfectly adapted to any type of PCB by means of its many adjustable components and its 3 adjustable clearance positions 22, 45 or 65 mm / 0.86, 1.77 or 2.55 in.

By means of JBC Software, the Preheater can be synchronized with other JBC Hot Air, Soldering Stations as well as Fume Extractor equipment in order for them to work jointly and to perform your rework process optimally.

Downloads & Resources

Selectable Temperature
50 to 250 ºC / 120 to 482 ºF

Heating area
108 x 70 mm / 4.25 x 2.75 in

Temperature measurement
Thermocouple type K

Connectivity
USB-B (rear)

Software PC

USB-A (front)
Firmware update / Graphics management

Robot
RS-232 remote control

Aux
Console connection

Pedal
Connect a pedal (ref.P-005) to control the heater.

ESD/EOS
ESD safe

Maximum power
500 W

Ambient operating temp.
10 – 50 ºC / 50 – 122 ºF

Dimensions and weight
Heater unit

179 x 165 x 42 mm / 3.10 kg.
7.05 x 6.50 x 1.65 in / 6.83 lb.

PHSK Small Preheater Set

It features three work modes:

Power Mode allows working at a fixed power level with the option of using protection thermocouple.

Temperature Mode keeps the PCBA at a selected temperature, using the regulation thermocouple and, optionally, protection thermocouples.

Profile Mode allows control of the heating rate of the PCBA by the use of a control and protection thermocouple, without exceeding the recommended limit levels in each application. It features 22 customizable profiles.

Up to four thermocouples can be connected in any of the three work modes.

PSS Small PCB Support is perfectly adapted to any type of PCBs by means of its many adjustable components and its 3 adjustable clearance positions 28, 50 or 70 mm / 1.1, 2 or 2.8 in.

By means of JBC Software, the Preheater can be synchronized with other JBC Hot Air, Soldering Stations as well as Fume Extractor equipment in order for them to work jointly and to perform your rework process optimally.

Downloads & Resources

Heating area
65 x 135 mm (2.6 x 5.3 in) – 1 zone
130 x 235 mm (5.1 x 5.3 in) -2 zones

Temperature measurement
Thermocouple type K

Connectivity
USB-B (rear)

Software PC

USB-A (front)
Firmware update / Graphics management

ESD/EOS
ESD safe

Maximum power
600 W


Ambient operating temp.

10 to 40 ºC / 50 to 104 ºF

Dimensions and weight
Heater unit

195 x 288 x 42 mm / 4.78 kg.
7.68 x 11.34 x 1.65 in / 10.54 lb.

PHBK Large Preheater Set

It features three work modes:

Power Mode allows working at a fixed power level with the option of using protection thermocouple.

Temperature Mode keeps the PCBA at a selected temperature, using the regulation thermocouple and, optionally, protection thermocouples.

Profile Mode allows control of the heating rate of the PCBA by the use of a control and protection thermocouple, without exceeding the recommended limit levels in each application. It features 22 customizable profiles.

Up to four thermocouples can be connected in any of the three work modes.

PSB Large PCB Support is perfectly adapted to any type of PCBs by means of its many adjustable components and its 3 adjustable clearance positions 28, 38 or 48 mm / 1.1, 1.5 or 1.9 in.

By means of JBC Software, the Preheater can be synchronized with other JBC Hot Air, Soldering Stations as well as Fume Extractor equipment in order for them to work jointly and to perform your rework process optimally.

Downloads & Resources

Heating area
180 x 277 mm / 7.1 x 10.09 in – 1 zone
360 x 277 mm / 14.2 x 10.9 in -2 zones

Temperature measurement
Thermocouple type K

Connectivity
USB-B (rear)

Software PC

USB-A (front)
Firmware update / Graphics management

Aux
Console connection

Pedal
Connect a pedal to control the heater.

ESD/EOS
ESD safe

Maximum power
1800 W

Ambient operating temp.
10 – 50 ºC / 50 – 120 ºF

Dimensions and weight
Heater unit
426 x 444 x 41 mm / 9.70 kg.
16.77 x 17.48 x 1.61 in / 21.38 lb.

 

PHXK XL Preheater Set

It features three work modes:

Power Mode allows working at a fixed power level with the option of using protection thermocouple.

Temperature Mode keeps the PCBA at a selected temperature, using the regulation thermocouple and, optionally, protection thermocouples.

Profile Mode allows control of the heating rate of the PCBA by the use of a control and protection thermocouple, without exceeding the recommended limit levels in each application. It features 22 customizable profiles.

Up to eight thermocouples can be connected to which enables the operator to work in any of the three work modes.

PSX XL PCB Support is perfectly adapted to any type of PCBs by means of its many adjustable components and its 3 adjustable clearance positions 28, 38 or 48 mm / 1.1, 1.5 or 1.9 in.

By means of JBC Software, the Preheater can be synchronized with other JBC Hot Air, Soldering Stations as well as Fume Extractor equipment in order for them to work jointly and to perform your rework process optimally.

Downloads & Resources

Heating area
255 x 203 mm / 10.04 x 8 in – 1 zone
510 x 610 mm / 20 x 24 in – 6 zones

Temperature measurement
Thermocouple type K

Connectivity
USB-B (rear)

Software PC

USB-A (front)
Firmware update / Graphics management

ESD/EOS
ESD safe

Maximum power
5400 W

Dimensions and weight
Heater unit
790 x 664 x 42 mm / 23.00 kg.
31.10 x 26.14 x 1.65 in / 50.71 lb.